How to Install a Tub (Step By Step).
How to Install a Tub (Step By Step).
Blog Article
Are you currently trying to locate ideas around Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard task. If the old bathtub is easily available, the job can move rapidly; if you have to open a wall to get rid of the old tub and also place the brand-new tub, the task is much harder. In either case, the job is within a home handyman's skills, although you will certainly require an assistant to leave the old tub and set in the brand-new one. Make certain you have qualified on your own for the work and also fit attempting it. Rather than hiring a service provider to take control of a halfway-completed job, it is better to consider using one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This article will certainly assist you install a brand-new tub in your restroom if you have actually currently purchased a brand-new bathtub and do not need to change the setup of your previous water pipelines.
Your tools and product checklist need to comprise the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain any water continuing to be in the system. The process of eliminating the existing taps can be fairly troublesome due to the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and the sink. Secure the faucet in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap adapters. The previous kind needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using both wood boards under its feet, position the bath tub in the needed setting. The wood boards are practical in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by examining the level as well as changing the feet on the tub up until the spirit level reads degree.
To set up taps, fit the bottom of the furthest flexible tap adapter to the ideal supply pipeline by making a compression join; then do the same for the other faucet.
Switch on the supply of water and examine all joints and also brand-new pipework for leaks and tighten them if necessary. Load the tub and additionally inspect the overflow outlet and the normal electrical outlet for leakages.
Finally, fix the bath paneling as described in the supplier's user's manual. Tiling and sealing around the bath tub must wait until the bath tub has actually been used at the very least once as this will certainly resolve it into its last setting.
Getting ready for the Installation
Firstly, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to split an inflexible seal, triggering the water to pass through the wall in between the bathroom and the tiling, causing difficulties with dampness as well as possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bath tub with water prior to securing, to enable the motion experienced when the bathtub remains in use. The sealant can break relatively early if you do not take into consideration this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the tiles using waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very focused on A Step-by-Step Guide to Installing a Bathtub and I am hoping you liked the page. Those who enjoyed reading our blog entry plz do not forget to share it. Thanks a lot for going through it.
Request Free Estimate Report this page